Contact Fax
0552-4070672
PRODUCTS
Introduce
The series dip switch is used to measure the change of biaxial tilt Angle. When the dip Angle of the measured object is less than the preset alarm Angle, the dip switch outputs high voltage signal, the voltage is equal to the power supply voltage. When the tilt Angle of the measured object is greater than the preset alarm Angle, the tilt switch outputs low voltage signal at this time, and the voltage is about 0V. The zero setting button is used to set the horizontal zero reference point.
power supply voltage |
24(9~36)VDC |
Sensitivity |
3% |
Working current |
30 mA |
distinguishability |
0.1 ° |
Measurement of shaft |
X、Y double-shaft
|
Measurement accuracy |
±0.1° |
Measuring range |
-30°~+30° |
Working time |
80000~100000Hr |
output signal |
switching value |
Working temperature |
-30℃~ 85 ℃ |
Alarm Angle |
X:±1.5° Y: ±3° |
Storage temperature |
-40℃~85℃ |
Product certification |
CE Certification
|
Corresponding frequency |
2s |
Protection grade |
IP67 |
Anti vibration indicators |
>3500 g |
DE chi 4 core plug-in models for DT04-4 p;
Series dip switch is used for measuring the change of the dual-axis tilt Angle, when the Angle is less than the preset alarm when the Angle of object to be tested, dip switch output voltage signal, high voltage size is equal to the power supply voltage; When the tilt Angle is greater than the preset alarm object to be tested, the dip switch output low voltage signals, voltage size is approximately equal to 0 v. Zero setting buttons to set the level zero
power supply voltage |
24(9~36)VDC |
Sensitivity |
3% |
Working current |
30 mA |
distinguishability |
0.1 ° |
Measurement of shaft |
X、Y double-shaft
|
Measurement accuracy |
±0.1° |
Measuring range |
-30°~+30° |
Working time |
80000~100000Hr |
output signal |
switching value |
Working temperature |
-30℃~ 85 ℃ |
Alarm Angle |
X:±1.5° Y: ±3° |
Storage temperature |
-40℃~85℃ |
Product certification |
CE Certification
|
Corresponding frequency |
2s |
Protection grade |
IP67 |
Anti vibration indicators |
>3500 g |
Decci 4-core plug-in model is DT04-4;
During installation, the mounting surface of the Angle switch should be kept parallel to the target surface of the measured wood, and the influence of dynamic and acceleration on the Angle switch should be reduced.
安装示意图
1. Zero setting button (set relative horizontal zero)
The zero setting button belongs to the hidden key, the key is hidden under the PVC panel;
Operation method: Hold down the zero setting button for 7 seconds, and the Pilot indicator blinks for 3 times (red). The setting is successful.
2, Lamp light
Lamp is the power indicator, as long as the Angle switch sensor is energized, this Lamp is always on (green).
3. Pilot indicator light (red)
This indicator light has two functions.
A: Zero success prompt (flashing 3 times);
B: When the Angle of the measured surface exceeds the set warning Angle, the Angle switch sensor will start to alarm and output low voltage signal, the signal size is about equal to zero volt. When the alarm is reported, the Pilot indicator continues to flash red.
When the power is off or the alarm is deactivated, the Pilot indicator stops flashing. Enter the normal working state.
Related Applications
Contact Fax: 0552-4070672
Website: www.sunmoon-china.com
Mailbox: sales@sunmoon-china.com
Add: Sun Moon Science and Technology Park, No. 985, Xingzhong Road, High-tech Zone, Bengbu, Anhui, China
About Us
Company Profile
Corporate History
Honor
Company Culture
Photo Gallery
Products
Force measurement and load cell
Wireless digital sensor
Temperature and pressure sensor
Angle, displacement, speed sensor
Oilfield measurement and control systemWeighing control system
Solution
Weighing logistics network solutions
Construction machinery sensor solutions
Oil and gas IoT solutions
Follow Us
Copyright © 2020 Bengbu Riyue Instrument Research Institute Co., Ltd. 皖ICP备19017385号-1 Powered by: www.300.cn